T5-DR BRECOFLEX® polyurethane timing belt
Version:
- Reinforced back of the belt, 2.5 mm larger belt width
- Preferred belt widths: 16, 25, 32, 50, 75, 100 mm
- In-between widths, larger widths and other dimensions are possible on request
Available endless lengths:
- For standard lengths refer to table
- Under 1,075 mm: further lengths on request
- Over 1,075 mm: any number of teeth available (minimum purchase amount for intermediate lengths on request)
- Over 15,000 mm: please enquire
Please consider our warranty.
Belt width b [cm]
\begin{align}
b& = {F_U \over {z_e \cdot F_{Uspez}}} && F_U [N] \\
b& = {100 \cdot M \over {z_1 \cdot z_e \cdot M_{spez}}} && M [Nm]\\
b& = {1000 \cdot P \over {z_1 \cdot z_e \cdot P_{spez}}} && P [kW]
\end{align}
Load bearing characteristics of the drive
when belt width [cm] is
\begin{align}
F_{U}& = {F_{Uspez} \cdot z_e \cdot b} &&[N]\\
M& = {{M_{spez} \cdot z_1 \cdot z_e \cdot b} \over {100}} &&[Nm]\\
P& = {{P_{spez} \cdot z_1 \cdot z_e \cdot b} \over {1000}} &&[kW]
\end{align}
Number of teeth in mesh
\begin{align}
z_{e max}& = {12}\\
z_e& = {{{z_1} \over {180}} \cdot \arccos{{t \cdot (z_2 - z_1)} \over {2\pi \cdot a}}}\\
\end{align}
1. Tooth shear strength
specific belt tooth strength
Rotational speed n [rpm] | Fuspez [N/cm] | Mspez [Ncm/cm] | Pspez [W/cm] | Rotational speed n [rpm] | Fuspez [N/cm] | Mspez [Ncm/cm] | Pspez [W/cm] |
---|---|---|---|---|---|---|---|
0 | 24,000 | 1,910 | 0,000 | 2000 | 13,690 | 1,089 | 2,280 |
20 | 23,400 | 1,861 | 0,039 | 2200 | 13,380 | 1,065 | 2,450 |
40 | 22,900 | 1,819 | 0,076 | 2400 | 13,100 | 1,042 | 2,620 |
60 | 22,400 | 1,783 | 0,112 | 2600 | 12,840 | 1,021 | 2,780 |
80 | 22,000 | 1,751 | 0,147 | 2800 | 12,590 | 1,002 | 2,940 |
100 | 21,700 | 1,723 | 0,180 | 3000 | 12,370 | 0,984 | 3,090 |
200 | 20,300 | 1,614 | 0,338 | 3200 | 12,160 | 0,967 | 3,240 |
300 | 19,300 | 1,536 | 0,483 | 3400 | 11,960 | 0,951 | 3,390 |
400 | 18,550 | 1,476 | 0,618 | 3600 | 11,770 | 0,936 | 3,530 |
500 | 17,930 | 1,427 | 0,747 | 3800 | 11,590 | 0,922 | 3,670 |
600 | 17,410 | 1,385 | 0,870 | 4000 | 11,420 | 0,909 | 3,810 |
700 | 16,960 | 1,349 | 0,989 | 4500 | 11,030 | 0,878 | 4,140 |
800 | 16,560 | 1,318 | 1,104 | 5000 | 10,680 | 0,850 | 4,450 |
900 | 16,200 | 1,289 | 1,215 | 5500 | 10,360 | 0,825 | 4,750 |
1000 | 15,880 | 1,263 | 1,323 | 6000 | 10,070 | 0,802 | 5,040 |
1100 | 15,580 | 1,240 | 1,428 | 6500 | 9,810 | 0,780 | 5,310 |
1200 | 15,310 | 1,218 | 1,531 | 7000 | 9,560 | 0,761 | 5,580 |
1300 | 15,060 | 1,198 | 1,632 | 7500 | 9,330 | 0,742 | 5,830 |
1400 | 14,830 | 1,180 | 1,730 | 8000 | 9,110 | 0,725 | 6,080 |
1500 | 14,610 | 1,162 | 1,826 | 8500 | 8,910 | 0,709 | 6,310 |
1600 | 14,400 | 1,146 | 1,920 | 9000 | 8,720 | 0,694 | 6,540 |
1700 | 14,210 | 1,131 | 2,010 | 9500 | 8,540 | 0,679 | 6,760 |
1800 | 14,030 | 1,116 | 2,100 | 10000 | 8,370 | 0,666 | 6,970 |
1900 | 13,850 | 1,102 | 2,190 |
Rotational speeds over 10000 rpm and/or belt speeds over 80 m/s are in need of a special drive design. Please request for our advice.
2. Tension cord strength [N]
permitted tensile force of the belt Fzul
Belt width b [mm] | 6 | 10 | 16 | 25 | 32 | 50 | 75 | 100 |
---|---|---|---|---|---|---|---|---|
SYNCHROFLEX T5 | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
SYNCHROFLEX T5-DL | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
SYNCHROFLEX T5-DL-E | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
SYNCHROFLEX T5-FA | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
SYNCHROFLEX T5-E | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
BRECOFLEX T5 | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
BRECOFLEX T5-E | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
BRECOFLEX T5-DL-E | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
BRECOFLEX T5-DL | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
BRECOFLEX T5-DR | 180 | 330 | 570 | 930 | 1200 | 1920 | 2940 | 3930 |
3. Belt weights [kg/m]
Belt width b [mm] | 6 | 10 | 16 | 25 | 32 | 50 | 75 | 100 |
---|---|---|---|---|---|---|---|---|
SYNCHROFLEX T5 | 0,014 | 0,024 | 0,038 | 0,060 | 0,077 | 0,120 | 0,180 | 0,240 |
SYNCHROFLEX T5-DL | 0,016 | 0,027 | 0,043 | 0,068 | 0,086 | 0,135 | 0,203 | 0,270 |
SYNCHROFLEX T5-DL-E | 0,016 | 0,027 | 0,043 | 0,068 | 0,086 | 0,135 | 0,203 | 0,270 |
SYNCHROFLEX T5-FA | 0,014 | 0,024 | 0,038 | 0,060 | 0,077 | 0,120 | 0,180 | 0,240 |
SYNCHROFLEX T5-E | 0,014 | 0,024 | 0,038 | 0,060 | 0,077 | 0,120 | 0,180 | 0,240 |
BRECOFLEX T5 | 0,013 | 0,022 | 0,034 | 0,052 | 0,067 | 0,105 | 0,163 | 0,210 |
BRECOFLEX T5-E | 0,013 | 0,022 | 0,034 | 0,052 | 0,067 | 0,105 | 0,163 | 0,210 |
BRECOFLEX T5-DL-E | 0,017 | 0,028 | 0,045 | 0,072 | 0,099 | 0,141 | 0,212 | 0,283 |
BRECOFLEX T5-DL | 0,017 | 0,028 | 0,045 | 0,072 | 0,099 | 0,141 | 0,212 | 0,283 |
BRECOFLEX T5-DR | 0,021 | 0,036 | 0,057 | 0,090 | 0,115 | 0,180 | 0,271 | 0,362 |
4. Flexibility
Minimum numbers of teeth, minimum diameter
( X ) without contraflexure
( X X ) with contraflexure
Belt type | Number of teeth zmin ( X ) | Tension roller dmin [mm] ( X ) | Number of teeth zmin ( X X ) | Tension roller dmin [mm] ( X X ) |
---|---|---|---|---|
SYNCHROFLEX T5 | 10 | 30 | 15 | 30 |
SYNCHROFLEX T5-DL | 10 | 30 | 15 | 30 |
SYNCHROFLEX T5-DL-E | 10 | 18 | 12 | 18 |
SYNCHROFLEX T5-FA | 10 | 30 | 15 | 30 |
SYNCHROFLEX T5-E | 10 | 18 | 12 | 18 |
BRECOFLEX T5 | 10 | 30 | 15 | 30 |
BRECOFLEX T5-E | 10 | 18 | 12 | 18 |
BRECOFLEX T5-DL-E | 12 | 18 | 12 | 18 |
BRECOFLEX T5-DL | 15 | 30 | 15 | 30 |
BRECOFLEX T5-DR | 20 | 30 | 20 | 60 |